Berikut ini adalah code error yang sering muncul di mesin fotocopy Canon serta Rincian tabel Error Kode Kesalahan yang mengacu pada cara memperbaiki kesalahan Fotocopy Canon iR2270 / iR2870 / iR3570 / iR4570 / iR2270N /iR2870N / iR3570N / iR4570N / iR2230 / iR3530/ iR3025/ iR3035/ iR3045/ iR3235/ iR3245/ IR2535
E261-0000 Error Code:
Because main power supply PCB is faulty Canon iR2270 / iR2870 / iR3570 / iR4570 / iR2270N /iR2870N / iR3570N / iR4570N / iR2230 / iR3530/ iR3025/ iR3035/ iR3045/ iR3235/ iR3245/ IR2535Description
In a certain inspection case, the error code appeared; however, replacement of the main power supply PCB solved it.
Field Remedy
When the symptom has occurred, re-insert J210 connector of the main power supply PCB. If the symptom still occurs, replace the PCB with a new one.
E261-0000
Error Code can be displayed when the zero-cross signal is not detected for 500msc or more when the relay is on.FM2-0260 Main Power Supply PCB Assembly (120V)
FM2-0245 Main Power Supply PCB Assembly (230V)
E315-000d Error Code:
Because main controller PCB is faulty Canon iR2270 / iR2870 / iR3570 / iR4570 / iR2270N /iR2870N / iR3570N / iR4570N / iR2230 / iR3530/ iR3025/ iR3035/ iR3045/ iR3235/ iR3245/ IR2535
Description
E315-000d was displayed; however, replacing the main controller PCB corrected it.
- E315-000d can be displayed when there is an error in JBIG decoding.
Field Remedy
When the symptom has occurred, re-insert all the connectors of the main controller PCB. If the symptom still occurs, replace the PCB with a new one.
FM2-4550 Main Controller PCB Assembly (for the iR4570 series)
FM2-4551 Main Controller PCB Assembly (for the iR2230)
Description of this code Canon iR2270 / iR2870 / iR3570 / iR4570 / iR2270N /iR2870N / iR3570N / iR4570N / iR2230 / iR3530/ iR3025/ iR3035/ iR3045/ iR3235/ iR3245/ IR2535
Description
When an error is detected during an operation of the finisher-S1, either of the following error codes is displayed. The cause of these error codes is a problem in the offset motor (M4), the offset HP sensor (PI6), or the finisher controller PCB.
- E520-0000 can be displayed when PI6 of the offset roller does not go ON even if M4 has been driven for 1000msec.
- E520-0002 can be displayed when PL6 of the offset roller does not go OFF even if M4 has been driven for 1000msec.
E602-0001 Error Code:
Progress bar stops at one-fifth point because hard disk (HDD) is faulty
Canon iR2270 / iR2870 / iR3570 / iR4570 / iR2270N /iR2870N / iR3570N / iR4570N / iR2230 / iR3530/ iR3025/ iR3035/ iR3045/ iR3235/ iR3245/ IR2535
Description
The error code was displayed when the progress bar stopped at about one-fifth point and then the machine kept such a situation for a while. As a solution, the hard disk (HDD) was replaced with a new one.
- E602-0001 can be displayed when the startup partition (BOOTDEV) cannot be found at startup.
Field Remedy
Turn the control panel switch and the main power switch OFF in sequence, re-connect the HDD, and then turn the main power switch ON. If the symptom still occurs, replace the HDD with a new one.
WM2-5216 HDD
Description
E716-0010 can be displayed when an error in the communication with the 3 Way Unit-A1 occurs within 5 sec after detecting the connection with the finisher.
The conceivable causes are the open-circuit of the cable, poor connection of the connectors J741 and J2107F, faulty 3 Way Unit-A1 driver PCB, and faulty DC controller PCB.
E315-000d was displayed; however, replacing the main controller PCB corrected it.
- E315-000d can be displayed when there is an error in JBIG decoding.
Field Remedy
When the symptom has occurred, re-insert all the connectors of the main controller PCB. If the symptom still occurs, replace the PCB with a new one.
FM2-4550 Main Controller PCB Assembly (for the iR4570 series)
FM2-4551 Main Controller PCB Assembly (for the iR2230)
E520 Error Code:
Description of this code Canon iR2270 / iR2870 / iR3570 / iR4570 / iR2270N /iR2870N / iR3570N / iR4570N / iR2230 / iR3530/ iR3025/ iR3035/ iR3045/ iR3235/ iR3245/ IR2535
Description
When an error is detected during an operation of the finisher-S1, either of the following error codes is displayed. The cause of these error codes is a problem in the offset motor (M4), the offset HP sensor (PI6), or the finisher controller PCB.
- E520-0000 can be displayed when PI6 of the offset roller does not go ON even if M4 has been driven for 1000msec.
- E520-0002 can be displayed when PL6 of the offset roller does not go OFF even if M4 has been driven for 1000msec.
E602-0001 Error Code:
Progress bar stops at one-fifth point because hard disk (HDD) is faulty
Canon iR2270 / iR2870 / iR3570 / iR4570 / iR2270N /iR2870N / iR3570N / iR4570N / iR2230 / iR3530/ iR3025/ iR3035/ iR3045/ iR3235/ iR3245/ IR2535
Description
The error code was displayed when the progress bar stopped at about one-fifth point and then the machine kept such a situation for a while. As a solution, the hard disk (HDD) was replaced with a new one.
- E602-0001 can be displayed when the startup partition (BOOTDEV) cannot be found at startup.
Field Remedy
Turn the control panel switch and the main power switch OFF in sequence, re-connect the HDD, and then turn the main power switch ON. If the symptom still occurs, replace the HDD with a new one.
WM2-5216 HDD
E716-0010 Error Code:
Occurs when machine is equipped with 3 Way Unit-A1Description
E716-0010 can be displayed when an error in the communication with the 3 Way Unit-A1 occurs within 5 sec after detecting the connection with the finisher.
The conceivable causes are the open-circuit of the cable, poor connection of the connectors J741 and J2107F, faulty 3 Way Unit-A1 driver PCB, and faulty DC controller PCB.
E732-0001 Error Code:
Because Reader Controller PCB is faultyDescription
The error code was displayed and the indication "R-CON" was not displayed under the service mode screens [VERSION] and [CLEAR]. Consequently, both the version check of the ROM on the reader controller PCB and the clear of the RAM were impossible in service mode. However, these symptoms were corrected by replacing the reader controller PCB with a new one.
- E732-0001: DDI-S communication error
Field Remedy
When the symptom occurs, re-insert all connectors of the reader controller PCB. If the symptom still occurs, replace the PCB with a new one.
FG3-3765 Reader Controller PCB Assembly
E732-0001 Error Code:
Because DIMMs have poor connection Canon iR2270 / iR2870 / iR3570 / iR4570 / iR2270N /iR2870N / iR3570N / iR4570N / iR2230 / iR3530/ iR3025/ iR3035/ iR3045/ iR3235/ iR3245/ IR2535
Description
In the field, the error code was displayed. However, it was corrected by re-inserting the DIMMs.
- E732-0001 can be displayed when the DDI-S communication error occurs.
Field Remedy
1. Re-insert the connector J1014 (for DDI communication) on the Main controller PCB.
2. If the symptom still occurs, re-insert the DIMM connected to the main controller PCB (J1004) and the DC controller PCB (J381).
E733-0001 Error Code is displayed at FAX reception/transmission; however it is solved by switching OFF/ON
Description
In the field, the error code was displayed. However, it was corrected by re-inserting the DIMMs.
- E732-0001 can be displayed when the DDI-S communication error occurs.
Field Remedy
1. Re-insert the connector J1014 (for DDI communication) on the Main controller PCB.
2. If the symptom still occurs, re-insert the DIMM connected to the main controller PCB (J1004) and the DC controller PCB (J381).
E733-0001 Error Code is displayed at FAX reception/transmission; however it is solved by switching OFF/ON
E001-0000 Error Code:
Because main power supply PCB is faulty Canon iR2270 / iR2870 / iR3570 / iR4570 / iR2270N /iR2870N / iR3570N / iR4570N / iR2230 / iR3530/ iR3025/ iR3035/ iR3045/ iR3235/ iR3245/ IR2535
Description
E001-0000 was displayed after a copy job was completed; however, replacing the main power supply PCB solved this code.
- E001-0000 can be displayed when the main thermistor detects the temperature of more than 250 deg. C for more than 200msec continuously.
Field Remedy
When the symptom has occurred, re-insert all the connectors of the main power supply PCB. If the symptom still occurs, replace the PCB with a new one.
FM2-0260 Main Power Supply PCB Assembly (for the 120V machine)
FM2-0245 Main Power Supply PCB Assembly (for the 230V machine)
14.2.8.3 E014-0002 Error Code/Abnormal sound from fixing assembly: Because cleaning roller mounts (front/rear)
Description
E001-0000 was displayed after a copy job was completed; however, replacing the main power supply PCB solved this code.
- E001-0000 can be displayed when the main thermistor detects the temperature of more than 250 deg. C for more than 200msec continuously.
Field Remedy
When the symptom has occurred, re-insert all the connectors of the main power supply PCB. If the symptom still occurs, replace the PCB with a new one.
FM2-0260 Main Power Supply PCB Assembly (for the 120V machine)
FM2-0245 Main Power Supply PCB Assembly (for the 230V machine)
14.2.8.3 E014-0002 Error Code/Abnormal sound from fixing assembly: Because cleaning roller mounts (front/rear)
Description
As a result of inspection, the following was found: One of the cleaning roller mounts is damaged and causes the fixing heatsink roller to fall down, resulting
in abnormal sound and E014-0002.
Field Remedy
When the symptom has occurred, replace the cleaning roller mount (front/rear) with a new one.
FM2-1775 Cleaning Roller Mount Unit (Front)
FM2-1776 Cleaning Roller Mount Unit (Rear)
E024-0001 Error Code:
DescriptionE024-0001 can be displayed under the following conditions:
- iR4570/3570/3530 series When the disconnection of the wire used for detecting the connection of the toner sensor (TS1) has been detected for 7.5 min without interruption. (12.5 min
in the manual/envelop cassette feeding)
- iR2870/2270/2830/2230 series, When the disconnection of the wire used for detecting the connection of the toner sensor has been detected for 12.5 min without interruption.
Field Remedy
When the symptom occurs, re-insert the connector J3405L. If the symptom still occurs, replace the sensor with a new one.
FK2-0358 Toner Sensor
E024-0001 Error Code: Because toner stays in developing assembly toner sensor (TS1) Canon iR2270 / iR2870 / iR3570 / iR4570 / iR2270N /iR2870N / iR3570N / iR4570N / iR2230 / iR3530/ iR3025/ iR3035/ iR3045/ iR3235/ iR3245/ IR2535
Description
As a result of inspection, the following was found. Toner gets in the developing assembly toner sensor (TS1) and eludes toner stirring operation, resulting in
the symptom. However, re-attachment of the sensor solves the symptom.
Field Remedy
When the symptom has occurred, make the following selections in service mode [COPIER > I/O > DC-CON] and check the setting for the bit1 of [P021]. If
the setting is "1", re-attach the toner sensor.
E024-0001 Error Code: The toner level sensor has an open-circuit.
FK2-0358 Toner Sensor
14.2.8.6 E110-0001 Error Code: Because DC controller PCB is faulty
Description
Since E110-0001 was displayed, the DC controller PCB was replaced with a new one for solution.
- E110-0001 can be displayed when the scanner motor causes a problem.
Field Remedy
When the symptom has occurred, re-insert all the connectors of the DC controller PCB. If the symptom still occurs, replace the PCB with a new one.
FM2-2779 DC Controller PCB Assembly (for iR3570/iR4570)
FM2-2767 DO Controller PCB Assembly (for iR2270/iR2870)
14.2.8.7 E202-0002 Error Code: Because reader controller PCB is faulty
Description
E202-0002 error code was displayed
however, replacing the reader controller PCB corrected the symptom.
- E202-0002 can be displayed when there is an error in the detection of the CIS home position.
Field Remedy
When the symptom has occurred, re-insert all the connectors of the reader controller PCB. If the symptom still occurs, replace the PCB with a new one.
FG3-3765 Reader Controller PCB Assembly
14.2.8.8 E244 Error Code: Occurs when formatting service part hard disk drive (HDD)
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /
Field Remedy
The service support tool (SST) has been upgraded. When the HDD is replaced with a service part one, format it using SST version 3.04 or later.
Description
In the field, the error code was displayed when formatting a service part HDD. Because SST of version 3.03 or younger was used.
- E202-0002 can be displayed when there is an error in the detection of the CIS home position.
Field Remedy
When the symptom has occurred, re-insert all the connectors of the reader controller PCB. If the symptom still occurs, replace the PCB with a new one.
FG3-3765 Reader Controller PCB Assembly
14.2.8.8 E244 Error Code: Occurs when formatting service part hard disk drive (HDD)
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /
Field Remedy
The service support tool (SST) has been upgraded. When the HDD is replaced with a service part one, format it using SST version 3.04 or later.
Description
In the field, the error code was displayed when formatting a service part HDD. Because SST of version 3.03 or younger was used.
Code: E000-0001
- Description:
Remedy:
Atur ulang kondisi dalam mode layanan: COPIER> FUNGSI> CLEAR> ERR. Ganti termistor utama. Ganti PCB pengontrol DC.
Code: E001-0000
Description: Suhu rakitan pemasangan sangat tinggi.
Rangkaian perangkat keras mendeteksi panas berlebih dari termistor utama atau sub untuk 200 msec.
Remedy: Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR. Replace the main thermistor. Replace the DC controller PCB.
Code: E001-0001
Description:The temperature of the fixing assembly is abnormally high.
The hardware circuit detects overheating of the main or sub thermistor for 200 msec.
Remedy:Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR. Replace the DC controller PCB.
Code: E001-0002
Description:The temperature of the fixing assembly is abnormally high.
The reading of the sub thermistor is 295 deg C or more continuously for 200 msec.
Remedy:Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR. Replace the sub thermistor. Replace the DC controller PCB.
Kode: E007-0000
Deskripsi:
Rotasi film pemasangan rusak. Ketika motor penguat berputar, sinyal marker tidak terdeteksi selama 6 detik dengan pembacaan termistor utama menunjukkan 100 derajat C atau lebih.
Ramuan:Atur ulang kondisi dalam mode layanan: COPIER> FUNGSI> CLEAR> ERR. Ganti termistor utama. Ganti PCB pengontrol DC.
Ramuan:Atur ulang kondisi dalam mode layanan: COPIER> FUNGSI> CLEAR> ERR. Ganti termistor utama. Ganti PCB pengontrol DC.
Kode: E010-0001
Deskripsi:Rotasi motor utama rusak. Deteksi dilakukan setiap 100 msec setelah dimulainya putaran motor; namun, sinyal deteksi drive tidak ada selama 2 detik.Obat:Ganti motor utama. Ganti PCB pengontrol DC.
Code error yang sering muncul di mesin fotocopy Canon
Reviewed by Editor
on
Desember 22, 2018
Rating:
Reviewed by Editor
on
Desember 22, 2018
Rating:
1 komentar:
ilmu yang sangat berguna sekali nie... terima kasih.
salam
https://arjunafotocopysidareja.blogspot.com/
Posting Komentar